AIR MOVER OWNER’S MANUAL
MODELS: 120 VOLT AM2400D (DAISY CHAIN)
VV78112
Rev. 2016(07.14)
TABLE OF CONTENTS
| Language | Section | Pages |
|---|---|---|
| ENGLISH | OPERATING INSTRUCTIONS | 1-8 |
| FRANÇAIS | DIRECTIVES OPERATIONNELLES | 9-11 |
| ESPAÑOL | INSTRUCCCIONES DE FUNCIONAMIENTO | 12-14 |
SAFETY PRECAUTIONS
All operators shall read, understand and exercise the following safety precautions:
- Do not operate machine:
- Unless trained and authorized.
- Unless you have read and understand the operators manual.
- Inflammable or explosive areas.
- With a damaged cord or plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- With the use of extension cords.
- Before operating machine:
- Make sure all safety devices are in place and operate properly.
- When using machine:
- Do not pull machine by cord or plug.
- Do not pull cord around sharp edges or corners.
- Do not unplug machine by pulling on the cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated surfaces.
- Report machine damage or faulty operation immediately.
- Before leaving or servicing machine:
- Turn off machine.
- Unplug cord from outlet.
- When servicing machine:
- An experienced technician should only perform service work.
- Unplug cord from outlet.
- Use manufacturer supplied or approved replacement parts.
GROUNDING INSTRUCTIONS
General – This air mover shall be grounded while in use to protect the operator from electrical shock. The machine is provided with a three – conductor cord and a three – contact grounding type attachment plug to fit the proper grounding type receptacle.
The green (or green & yellow) conductor in the cord is the grounding wire. Never connect this wire to anything other than the grounding pin of the attachment plug.
Make sure that all the safety functions are normal, and ensure that the actual operation voltage is in accordance with the required voltage rate.Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine.
This machine is intended for commercial use only. It is constructed for use in an indoor environment and is not intended for any other use.
BASIC OPERATION
- Check the machine for any obstructions in fan prior to operation.
- If an item blocks the intakes of the air mover, this will hurt the performance of the machine, and could cause the motor to overheat.
- Adjust machine to desired position for operation by pulling it back to its preset height adjustments.(Air blower drying direction without Transport kit refer to Figure 1 )
- Plug power cord into a grounded outlet.
- Do not use an extension cord in conjunction with the standard power cord.
- This machine has 3 power settings. Turn the power knob to the desired speed.
- Low = 1 Med = 2 High = 3.
- To stop the machine at any time, simply turn the power knob to the “off” position.
- Never stick any object into the air inlet vents or the air outlet vent.
DAISY CHAIN
The AM2400D can be connected in a “Daisy Chain” allowing for two aditional AM2400D units work together on one circuit refer to Figure 2.
MAINTENANCE
To keep this machine performing well for many years, please follow the following maintenance procedures:
- Unplug machine as soon as you are done using it.
- Check power cord for any damage. If any damage is detected, replace the cord immediately.
- Lubricate the handle assembly and wheels with a water resistant lubricant every month.
- Check machine for loose or missing nuts and bolts, and replace as necessary.
- Clean the outside of the machine with a mild cleaner.
PART LIST
AM2400D part list drawing refer to Figures 4+5
WIRING DIAGRAM
120V AM2400D wiring diagram refer to Figure 6
AIR BLOWER SPECIFICATION
Air blower specification refer to Figure 7
Advance and Nilfisk are trademarks of Nilfisk A/S. Southeastern Equipment & Supply is an independent dealer.
