Kaivac 1050M Operator Manual

OPERATOR'S MANUAL

1050M‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​​‌​​​‌​⁠​​​​‍⁠‍‌‌‌⁠⁠‌‍​⁠​‌‌‍​‌‌‌​‍

©2026 Kaivac, Inc. All rights reserved

Kaivac Limited Warranty

Kaivac, Inc. provides this Limited Warranty for the applicable Products and periods stated below, subject to certain limitations, to the original purchaser against defects in material or workmanship when the Product is properly set up, operated, maintained, and stored in accordance with Kaivac's recommendations. Unless otherwise extended by written agreement, for any covered defects in materials or workmanship, Kaivac will repair or replace the Product at its sole option, during the following coverage period(s) for each Product, its respective material(s) and/or component(s) as follows:‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​​‍​​​‌​⁠​​​‌‍⁠‌‍⁠​‌⁠​‍⁠​⁠​‍​​‍​‌​‌

Limited Warranty Coverage and Periods of Warranty:

Kaivac extends the Limited Warranty on designated components of the Product for the coverage periods as specified below.

1. TANK AND TROLLEY LIMITED WARRANTY. The vacuum tank and trolley (“Tank & Trolley”) are warranted to be free from defects in workmanship and materials for a period of Five (5) Years from the date the user purchases the Product.
2. VACUUM MOTOR and PUMP LIMITED WARRANTY (excluding Battery). The Battery interface and components (excluding Lithium-ion battery), vacuum motor, and pump (collectively “Components”) are warranted to be free from defects in workmanship and materials for a period of Three (3) Years from the date the user purchases the Product. A Limited Lifetime Warranty for the OMNIFLEX vacuum motor is available to customers who purchase a Kaivac chemical subscription concurrently with the initial purchase of the OMNIFLEX unit and maintain the subscription without interruption for the duration of ownership. Eligibility for the warranty is conditioned upon the exclusive use of Kaivac-supplied chemicals in the OMNIFLEX unit. Any cancellation, lapse, or discontinuation of the subscription will immediately terminate the Limited Lifetime Warranty.
3. LABOR LIMITED WARRANTY. Kaivac further warrants to the original purchaser any labor authorized by Kaivac and performed by a service provider, chosen or approved by Kaivac against defects in material or workmanship for One (1) Year from the date the labor was performed, not to exceed the original warranty on the part.
4. BATTERY LIMITED WARRANTY. The lithium-ion battery (“Battery”) is warranted to be free from defects in workmanship and materials for a period of Two (2) Years from the date the user purchases the Product.
5. REPLACEMENT PARTS. Replacement parts (“Parts”), which excludes Accessories, are warranted to be free of defects in workmanship and materials for a period of ninety (90) days from the date the user purchases the Part.

Limits of Warranty and Exclusions:

Kaivac's liability under this Limited Warranty is limited to the repair or replacement of a defective Product, at its sole discretion. This Limited Warranty DOES NOT include any warranty coverage for accessories to the Product(s) including, but not limited to accessory squeegee blades and wheels, hoses, seals, gaskets, cords, casters, HEPA filter cartridges, chemical feed caps, spray gun, GFCI, and vacuum wand assembly (individually, an “Accessory” and collectively, “Accessories”).

This Limited Warranty shall not apply to any Products that have been repaired, altered, or modified in a way, so as in Kaivac's sole judgment, adversely affects the operation, performance, or durability, or changes the Product's intended use. The Limited Warranty shall not apply to any Products which, in Kaivac's sole judgment, have been subject to misuse, abuse, negligence or accident, nor to any Products that have not been operated and maintained in accordance with Kaivac's instructions and recommendations. Compliance with the Limited Lifetime Warranty for OMNIFLEX vacuum motor shall be determined solely by Kaivac. In addition, the Limited Warranty does not cover damage caused by the following, as determined solely by Kaivac:

• Any use inconsistent with the instructions and warnings for the Product;
• Use of high-foaming or corrosive chemicals;
• Use of a non-Kaivac battery or charger or improper installation of the Battery;
• Loss of IoT functionality resulting from failure to maintain network connectivity for the Product or to allow Kaivac-issued firmware, security certificate, or software updates to be applied;
• Use of Battery for more than Five (5) years after purchase;
• Any accident, neglect or failure to operate and maintain the Product according to Kaivac's instructions and warnings; and
• Any modification or attempt to modify the Product by anyone other than Kaivac or a Kaivac approved service provider.
• Normal wear and tear.

Kaivac Limited Warranty (Continued)

For warranty claims, the original purchaser shall be responsible for any freight, shipping, and travel costs associated with the repair or replacement provided for under this Limited Warranty. For warranty claims made outside the country of purchase, the original purchaser will be responsible for all import duty costs incurred.‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​​⁠​​​‌​⁠​​‌‍⁠‍‍⁠‍‍‍‍⁠‌‍‌‍‌​​‌⁠​⁠‌​

If Kaivac authorizes a repair, the repair warranty will not extend the time period of the of the original Product or Part's warranty period under this Limited Warranty.

If you obtain a replacement Product, this Limited Warranty applies to such replacement for the remainder of the original Product's warranty period.

Exclusions of Liability and Disclaimer of Implied Warranties: EXCEPT AS OTHERWISE EXPRESSLY STATED HEREIN, KAIVAC MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED FROM THIS LIMITED WARRANTY. TO THE EXTENT THEY CANNOT BE DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY. THIS LIMITED WARRANTY ALSO EXCLUDES INDIRECT, INCIDENTAL, CONSEQUENTIAL, AND SPECIAL DAMAGES. THIS EXCLUSION OF INDIRECT, INCIDENTAL, CONSEQUENTIAL, AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL PURPOSE. THE REMEDIES SET FORTH IN THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON UNDER THIS WARRANTY. SOME STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS, AND EXCLUSIONS IDENTIFIED ABOVE AND, AS A RESULT, THEY MAY NOT APPLY TO YOU.

Upon purchasing any Product, purchaser assumes all liability, all personal injury and property damage resulting from the handling, possession or use of such Product. No agent, employee or representative of Kaivac, nor any independent retailer and/or dealer, is authorized to bind Kaivac to any affirmation, representation or warranty regarding the Products except as specifically contained in this Limited Warranty. Kaivac may modify this Limited Warranty.

Consult Kaivac.com for current Product(s) information and Limited Warranty. For any questions or warranty service, please contact Kaivac Customer Service at 1/800-287-1136 (Outside the U.S. Call 513-887-4600).

Version 7-9-2026

Phone:

United States and Canada: 1-800-287-1136

International: 1-513-887-4600

Email:

[email protected]

For Technical Support Contact Form go to: https://www.kaivac.com/contactus.php and choose Technical\Support tab.

2680 Van Hook Avenue, Hamilton, OH 45015 / 800-287-1136 / kaivac.com

Protected by multiple US patents. Multiple patents pending. © Copyright Kaivac, Inc. 2026

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS
CONSULT KAIVAC.COM FOR THE MOST UP TO DATE SAFETY PRECAUTIONS
READ ALL INSTRUCTIONS BEFORE USING (THIS UNIT)‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‌​​​​‌​⁠​​‍⁠⁠‌⁠‌​‍‌⁠‌‌‍‍‌⁠​​‍‌⁠‍‌​

When using an electrical unit, basic precautions should always be followed, including the following:

GENERAL SAFETY INSTRUCTIONS (APPLICABLE TO CORDED AND BATTERY UNITS):

• For commercial use only.
• Use unit only as described in this Manual. Use only Kaivac's recommended attachments.
• Follow the maintenance instructions specified in this Manual.
• For indoor use only. Store indoors.
• Stay alert - watch what you are doing. DO NOT overreach or stand on unstable support. Keep good footing and balance at all times.
• Keep operating area clear of all persons.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• NO COMBUSTIBLES! Sparks inside the motor can ignite flammable vapors or dust. Do not use unit near combustible liquids and gases, or to pick up explosive dusts or gasoline.
• Know how to stop the unit and bleed pressures quickly. Be thoroughly familiar with the unit's controls before operating.
• DO NOT allow unit to be used as a toy and unit should not be operated by children. Close attention is necessary when used near children.
• Use extra care when cleaning on stairs.
• DO NOT operate the unit when fatigued or under the influence of alcohol or drugs.
• DO NOT put any object into unit's openings. Do not use with any of the unit's opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• DO NOT pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
• DO NOT operate without the Vacuum Motor Float Cage installed. If float is removed, reinstall by screwing back into place.
• DO NOT use without filters in place.
• Personal Protective Equipment (PPE): It is recommended to wear proper personal protective equipment as required by the chemical product label instructions used in conjunction with the unit. For Kaivac chemical products, refer to product label.

SPRAY SYSTEM SAFETY INSTRUCTIONS:

• DO NOT spray liquid from the unit or attachments onto electrical outlets or any electrical devices.
• Risk of injection or injury to persons - DO NOT direct discharge stream at persons.
• INJECTION HAZARD: Unit can cause serious injury if the spray permeates the skin. Do not point the spray gun at anyone or any part of the body. In case of permeation, seek medical aid immediately.
• THIS UNIT IS CAPABLE OF PRODUCING 500 PSI (3447 kPa). To avoid rupture and injury, do not operate this pump with components rated less than 500 PSI (3447 kPa) working pressure (including but not limited to spray guns, hose, and hose connections); and before servicing, cleaning or removal of any part, shut off power and relieve pressure.
• High pressure cleaners, such as this unit, shall not be used by children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or untrained personnel. Children should not play with the unit. Cleaning and user maintenance should not be performed by children.

CORDED UNITS SAFETY INSTRUCTIONS (APPLICABLE TO CORDED UNITS):

• Inspect cord and plug prior to use. Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors or dropped into water, do not use or charge and return unit to a Kaivac service center.
• This unit may also have been provided with a ground fault circuit interrupter (GFCI) built into the power cord. If replacement of the plug or cord is needed, use only identical replacement parts. Test the unit's ground fault circuit interrupter (GFCI) before each use.
• Turn off the unit before unplugging. Do not leave unit when plugged in. Unplug from outlet when not in use and before servicing.
• Turn off all controls before unplugging.
• Connect to a properly grounded outlet only. Do not remove ground pin on plug. See Grounding Instructions below.
• This unit comes with a grounded attachable extension cord. If cord is damaged, replace with equivalent 120v, 15amps, 14GA rated cord. This cord must be attached and mechanically secured using the provided cord connector to use the unit.
• The unit must be disconnected from any electrical or battery source when the unit is being cleaned or maintenance of unit or when replacing parts
• Keep all connections dry and off the ground. If using extension cord with unit, make sure the connection is above and off the floor and away from exposure to liquid.
• Keep the cord away from heated surfaces.
• DO NOT handle plug or unit with wet hands.
• DO NOT pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or corners. Do not run unit over cord. Keep cord away from heated surfaces.
• DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord.

IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)

SAVE THESE INSTRUCTIONS
CONSULT KAIVAC.COM FOR THE MOST UP TO DATE SAFETY PRECAUTIONS
READ ALL INSTRUCTIONS BEFORE USING (THIS UNIT)‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‌‌​​​‌​⁠​​⁠‌⁠‍‌​‍​⁠​‌‌​‌​‍‌⁠​​⁠‍​⁠

When using an electrical unit, basic precautions should always be followed, including the following:

BATTERY UNITS SAFETY INSTRUCTIONS (APPLICABLE TO BATTERY UNITS):

• Never use a battery that has been damaged in any way. Damaged batteries may exhibit unpredictable behavior.
• Never use or charge a damaged battery pack.
• ONLY USE with Kaivac, Inc. battery, and charger.
• Inspect the battery before each use for damage, dents, cracks, or holes.
• If included with legacy unit, the battery splash cover must remain in place. Without the battery splash cover, the battery housing may become damaged which may cause the battery to malfunction, which can result a fire, explosion, personal injury, and/or property damage.
• If your unit contains a chemical-resistant plastic protective helmet, consult the Helmet Addendum for additional instructions and warnings.
• Exposure of units to airborne polyunsaturated fats in the food service industry may cause deterioration of battery components. Failure to inspect and use as instructed may result in fire explosion, personal injury, or property damage.
• Under certain conditions, including damage or liquid infiltrating the battery's interior cells, the battery may emit smoke, sparks, or fire. Liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
• Stop use immediately if the battery or unit sparks or shows signs of fire. And may result in fire.
• If unit or battery emits fumes, smoke, sparks, or fire, discontinue use immediately. Do not touch battery. If unit can be safely moved, move outside to a well ventilated fire safe area away from people or combustible material.
• DO NOT attempt to repair, service or modify the batteries or charger. Contact Kaivac Technical Support with any issues.
• Disconnect the battery from the unit before making any adjustments, changing accessories, or storing unit. Such preventive safety measures reduce the risk of starting the unit accidentally.
• When charging battery, make sure charger or unit has at least 6 inches of clearance on all sides for adequate air flow.
• When battery is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Connecting or shorting the battery terminals together may cause burns or a fire.
• Keep heat sources, sparks, and flames away from batteries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery, picking up or carrying the unit. Do not carry the unit with your finger on the switch. Energizing an unit that has the switch on invites accidents.
• DO NOT allow battery to be submerged in water.
• DO NOT use a battery that has been submerged in water, or if water has infiltrated the battery housing even if it appears to be working.
• DO NOT charge batteries outdoors.
• DO NOT short-circuit the battery or charger terminals with conductive items such as paper clips. This can deliver high current.
• DO NOT crush or drop the battery.
• DO NOT expose a battery or unit to fire or excessive temperature. Exposure to fire or temperature above 265°F (130°C) may cause explosion.
• DO NOT use or store the NTC System or battery in refrigerated areas, in environments when the battery is in direct contact with liquids, or near flammable or combustible materials.
• DO NOT charge or store battery for extended time (1 month or more) in temperatures below 40°F (4°C).
• DO NOT remove any part of the battery, charging unit, or unit: If your unit has a chemical-resistant plastic protective helmet, do not remove it.
• DO NOT plug battery in while Vacuum Motor is in ON position. It may damage the system.
• DO NOT incinerate the battery even if it is non-working or severely damaged. The battery can explode in a fire.
• DO NOT leave battery connected to charger once the charger light is green. Leaving battery on charger will diminish the life of the battery
• Never dispose of the battery in the trash. It is important that your old, damaged battery is disposed of and/or returned as instructed by Kaivac Customer Care/Technical Support at 1-800-287-1136.

CHARGER/ELECTRICAL WARNINGS:

• Inspect the charger, cords, and connections prior to each use.
• Follow all charging instructions and do not charge the battery or unit outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
• Connect charging cord to a properly grounded outlet only. See Grounding Instructions.
• DO NOT use charger if it has a damaged cord or plug.
• DO NOT operate charger if it has received a sharp blow, been dropped, or damaged in any way.
• DO NOT handle charger, including charger plug and charger terminals, with wet hands while charger is plugged in or while inserting plug into electrical outlet.
• DO NOT leave charger plugged in when not in use.
• DO NOT plug in charger while Vacuum Head is in ON position. It may damage the unit's electrical system.
• DO NOT pull on charger cord to unplug. Grasp and pull the plug, not the cord.
• DO NOT carry charger by cord.

To recycle battery, call Kaivac Customer Care at 1-800-287-1136 to order a recycling box.
Disposal of batteries are regulated by federal law and must be done properly.‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‌‍​​​‌​⁠​​‌‌⁠​​​‌⁠​‍‌‌‌‍‍⁠⁠‌⁠‌‌​‍⁠

BATTERY INFORMATION

Keep Batteries at Room Temperature: Store between 32 and 113 degrees F (0°C to 45°C). Avoid battery exposure to extreme temperatures. If shelving battery longer than (1) month, deplete battery to 50% charge during storage period (two bars on the battery indicator).

Batteries Lose Capacity Over Time: Batteries naturally deteriorate over time whether being used or not. If battery use instructions are properly followed, batteries deteriorate at a rate of approximately 10% run time per year but may vary by patterns of use.

Fully Discharge vs. Partial Discharge and the Effect on Battery Cycles: Unlike lead acid batteries, the Lithium-ion battery used with Kaivac equipment is not damaged by full or partial discharging. The expected battery hours of use are approximately 600 hours and 400 charge cycles. If you discharge battery only to 80%, then the user can expect to get more cycles (500 cycles). With dual batteries make sure to alternate batteries per charge in order to maximize for life capacity.

Extended Storage: It is recommended to discharge to 50% capacity (two bars on the battery indicator) and store in a cool location (between 32°F to 113°F or 0°C to 45°C). To avoid battery impact, store battery laying down on its side on lowest shelf, and secured. If battery is dropped or experiences an impact or damage, discontinue use and replace. Never use a damaged battery, as a damaged battery may act in an unpredictable manner resulting in fire, explosion, property damage, or personal injury.

Battery Gauge: The Kaivac provided battery comes with a built-in Battery Gauge or which shows the approximate run time for the current charge remaining.

Replacement - End of Life: Rechargeable batteries eventually wear out. When your Kaivac Battery run time is less than 55% (i.e. 50 minutes for non-quick change and 33 minutes for Quick Change batteries), Kaivac recommends replacing your battery. Regardless of run time, contact Kaivac to replace your battery after 4 years. Consult kaivac.com for information on recycling your old battery through a licensed disposal facility.

GROUNDING INFORMATION

Grounding: Corded Units

GROUND FAULT CIRCUIT INTERRUPTER PROTECTION (for spray systems only)‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‌⁠​​​‌​⁠​​‍⁠⁠‌⁠​‍‍⁠‍⁠‍‍⁠‌⁠⁠⁠​‌‍⁠⁠​

If your unit is a corded unit, it has been supplied with a ground-fault circuit-interrupter(GFCI) built into the plug of the power-supply cord. This GFCI device provides additional protection from the risk of electric shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection.

If your unit is a corded unit, it is for use on a nominal circuit and has a grounding attachment plug. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this unit.

GROUNDING INSTRUCTIONS

If your unit is a corded unit, it must be grounded. If the unit should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This unit is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local electrical codes and ordinances.

This unit comes with a grounded attachable extension cord. If damaged, replace with Kaivac® (OEM) cord, or if necessary an equivalent cord rated 120V, 15 amps, 3-wire, 14 GA. This cord must be attached and mechanically secured using the provided cord connector to use the unit.

Grounding: Battery Units

GROUNDING INSTRUCTIONS

The charger must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This unit is equipped with a cord having equipment grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This unit is for use on a nominal circuit and has a grounding attachment plug. Make sure that the unit is connected to an outlet having the same configuration as the plug. No adapter should be used with this unit.

GROUNDING INFORMATION (CONTINUED)

Make sure your extension cord is in good condition and is the correct size for your unit. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gage number, the heavier the cord. An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating.‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‍​​​​‌​⁠​​‌​⁠‌‌⁠‌‌​⁠‌​​‌‍​​⁠‌‌‍⁠‍‌

Use only three-wire outdoor extension cords that have three-prong grounding receptacles that accept the unit’s plug.

To reduce the risk of disconnection of the unit’s cord from the extension cord during operations:

• Make a knot as shown in Figure 1 below:

Figure 1 - Method of securing the appliance cord to the extension cord set

Table 1 - Minimum gauge for extension cords

UNIT COMPONENTS

BASE UNIT ACCESSORIES

SETUP/BASIC OPERATION

INSTALLING BATTERY AND CHARGING

Battery units only‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​​‍‍​​​‌​⁠​​​⁠⁠‌​⁠​​​⁠⁠⁠⁠‌​‍‌‌‌⁠​‌⁠‌

See Figures 1 - 4, page 11

• Lower battery down into the battery housing.
• To see battery charge, press the charge indicator on the top of the battery.
• Connect the plug from the battery housing into the vacuum motor plug.
• To charge the battery, keep the battery in the battery housing. Locate the cord wrapped around the cleats connected to the battery housing, plug into an outlet to begin charging .

PREPARING UNIT FOR USE

See Figures 5 - 9, page 11

• The pump power cord is connected on the back panel of the spare water reservoir. Ensure this is connected to the battery housing power cord located on the back of the vac tank.
• Ensure Vacuum motor is in place on the vacuum tank. Ensure top clasps are secured. Ensure float cage is in place and clean.

• Locate switch panel on vacuum head. This is used to operate the vacuum function.
• Ensure vacuum tank clasps are secure. Locate tool tray on side of trolley bucket to place vacuum wand when not in use.
• Unplug battery from charger if applicable. Avoid getting water on unit.
• Inspect battery, housing, plug, cord, splash cover (if applicable), and helmet (if applicable) for damage, including cracks, separation, dents, holes, missing, pieces, and fraying cord or wires.

FILLING THE UNIT

See Figures 9 - 13, page 12

Ensure spigot is closed before filling.

• The spare water reservoir has a fill hose and lid. Fill as needed when using the spray gun.

• DO NOT fill the spare water reservoir with chemical. Use clean water only. Note the location of the site tubes.
• Fill in the designated opening near the water reservoir and vacuum tank.

• If using a Chemical packet, pour desired Chemical packet into the designated fill area of the trolley bucket, and ensure proper dilution of chemical is used.
• Note the location of the site tubes and gallon markings displayed for 5 to 8 gallons. For lesser quantity needs, the bottom of the label represents 2 gallons. For higher volume needs, the top of the label represents 10 gallons.
• If using a cleaning product that foams, use a foam inhibitor to cut excess. Pour 2 capfuls of inhibitor in the Vacuum Hose with Vac running to coat inside of Vacuum Hose.

• Foaming chemicals in tank may damage Vac Motor.

ACCESSORY ATTACHMENT USAGE

See Figures 14 - 20, page 12

• To attach different accessories to the end of the vacuum wand, start by loosening the coupler nut of the wand. Insert the accessory tool, and tighten the coupler nut.
• Ensure the brass ring inside the coupler nut of the vacuum wand stays in place and does not get lost when changing accessories or taking apart.
• To use accessories without the vacuum wand, push the desired accessory tool directly into the end of the yellow vacuum hose cuff connected to the side handle tube. Reconnect to tube when done with accessory use.
• You may use the provided dusting brush tool to vacuum fans and high surfaces with the vacuum wand.
• You may use the squeegee head brush head for stairways and surfaces such as tile and grout lines
• You may use the upholstery tool for spot cleaning.

CARPET & DRY VACUUM OPERATION

CARPET OPERATION

• Ensure unit is properly filled with appropriate amount of water and/or solution (Fig. 21).
• Ensure vacuum hose is connected to the tube on the side of the handle (Fig. 22).
• Lift the snap strap on the handle and ensure it is on the "CARPET" tab (Fig. 23).
• Turn the thumb throttle handle counter clockwise to "CARPET/OFF" position (Fig. 23).

• Locate the mixing tube valve and ensure it is in the "ON" position for dry vacuuming (Fig. 24).
• Turn the vacuum motor ON (I)
• Vacuum carpet as needed. For hard to reach areas, use provided accessories with vac hose or vac wand (Fig. 25).
• Use the upholstery tool for spot cleaning as needed (Fig. 26).
• Turn vacuum motor OFF (O) when job is complete.
• For transport mode, lift the strap to "UP" position.

HARD FLOOR & WET VAC OPERATION

HARD FLOOR OPERATION

• Ensure unit is properly filled with appropriate amount of water and/or solution (Fig. 27).

  

• Ensure vacuum hose is connected to the tube on the side of the handle (Fig. 28).

  

• Lift the snap strap on the handle and ensure it is on the “HARD FLOOR” tab (Fig. 29).
• Turn the thumb throttle handle counter clockwise to “HARD FLOOR” position (Fig. 29).

  

• Locate the mixing tube valve and ensure it is in the “OFF” position for wet vacuuming (Fig. 30).

  

• Turn the vacuum motor ON (I)
• Beginning at the rear of the area, begin dispensing solution, moving towards the front of the area (Fig. 31).

  

• Turn Spigot clockwise to the “OFF” position when job is complete.
• For extra detailing, vacuum floor surface diagonally to grout lines, reaching under shelves, seating etc. (Fig. 32).

  

• Slap & Tap: Once Vacuuming is complete, keep motor running. Slap Vacuum Wand on floor 3-4 times to dislodge debris from squeegee head. Then, invert Wand and Tap 4-5 times to dislodge any fluids or substance from Wand.
• Turn vacuum motor OFF (O) when job is complete.
• For transport mode, lift the strap to “UP” position.

SPRAY OPERATION

SPRAY OPERATION

• If using unit with chemical, prepare the cleaning chemical, make sure the Draw Tube is inserted into the Chemical Jug. Insert the Metering Tip as shown (see Metering Tip Selection Chart on the Metering Tip Bag). Then, screw the Chemical Cap onto the Chemical Jug and make sure the clear Chemical Line is connected to the Chemical Cap (Fig. 33).
• Place the chemical jug into the jug holder located on the spare water reservoir (Fig. 34).
• Ensure reservoir is filled with clean water before using spray gun.
• To use spray gun with chemical, turn the injector valve on the jug holder to "ON" position as shown (Fig. 35).
• To turn Spray Gun off or on, switch the valve connected to Spray Gun. The Spray Gun is connected to the Pressure Hose (Fig. 36).
• Operate the Spray Gun by pulling the nozzle out and twisting for low pressure pinpoint or fan spray. Pull nozzle back for high pressure pinpoint or fan spray. Chemicals applied in the Low Pressure setting only. Chemicals must be cleared from the Spray Line prior to High Pressure rinsing. To do this, turn OFF the Chemical Valve, then spray in Low Pressure settings for 15 seconds (Fig. 37).
• Turn the "PUMP" switch located on the battery housing ON (I) to begin using after preparing. Spray intended object with chemical in low pressure, and then turn the chemical valve OFF and clean with fresh water in high pressure (Fig. 38).

DAILY & GENERAL MAINTENANCE

The unit should be checked, emptied, and cleaned after each use.‌‌​⁠‍‍​‍‌‌‍​‌​​​‍​‌‍​​​​​‌​​​​​‌​⁠​​‌‍​​​​‌‍‍‌⁠‌⁠‌‌​‌⁠​⁠‌‍‌​

Unit should be turned OFF (O) unless specified.

EMPTYING THE VACUUM TANK

• If the Vacuum Motor shuts off before the job is complete, the Vacuum Tank may be full and need to be emptied. Lift the Vacuum Head to check liquid level inside the Vacuum Tank.
• To begin the dumping process, you must first press down on the Cap and turn counter-clockwise (Fig. 34).



• Once cap is removed, lower Dump Hose into appropriate sink/drain (Fig. 35).

CLEANING UNIT

• When work is complete, vacuum excess cleaning solution from the bucket for 5 seconds to clean out and degrease the Vacuum Hose (Fig. 36).



• Alternatively, you can also turn the Vacuum ON (I) and dispense solution into Vacuum Hose to clean Hose and Tank.
• Rinse Vacuum Tank thoroughly at clean-up sink, preferably with hot water. Rinse out Trolley Bucket (Fig. 37).

CLEANING UNIT FILTERS

• Lift the Vacuum Head. Clean and spray the Float Cage located inside the Vacuum Head. Ensure Float Cage is in place. Clean Float Cage regularly Do not use if Float Cage is not in place (Fig. 38).



• If unit contains mesh Filter Bag located inside the Vacuum Tank, before starting each new cleaning process, remove Filter Bag, dump any debris out, spray clean, and then replace back into the Filter Bag Frame (Fig. 39).



• Rinse plastic finger filter and foam filter inside Trolley Bucket following to clear debris (Fig. 40).

SQUEEGEE BLADES & ACCESSORIES

• Replace mop pads by aligning with the spreader, and folding under (Fig. 41).



• Check for worn squeegee blades. Worn blades cause streaking and loss of vacuum suction.
• Replace with new every 6-8 weeks. Ensure squeegee blades are replaced with the ribbed portion facing outwards (Fig. 42).



• Clean off accessories and build-up on parts and tools.

UNIT & MAINTENANCE

ELECTRICAL DIAGRAM

TROUBLESHOOTING CLOGS

Clog Areas of the unit are circled above

1. Check the Vacuum Hose for clogs with the Vacuum Motor running.
   Starting at the squeegee head and working forward to the vacuum tank, pull off the Vacuum Hose one connection at a time to find a clog in the Vacuum Hose.
2. Check Vac Hose Connection on Handle.
3. Check Vac Hose connection at the Mixing Tube.
4. Check for clog at inlet of the Vacuum Tank.
   Check for clog at the inlet of Vacuum tank circled above.
5. Check the yellow mesh filter inside the tank to see if full. Empty and replace if applicable.

TROUBLESHOOTING

TROUBLESHOOTING

TROUBLESHOOTING